Hi Evochronians,
i don't know exactly since when this happened but i cannot go into cryo mode in space anymore.
I have 0 thrust, it doesn't matter if i'm in deep sapce or around a planet. It doesn't work.
System always complain with "unable to save, must be stationary to engage cryo mod in open space"
Any ideas ? Screenshot provided as link:
http://imgur.com/a/zSMFv
unable to go into cryo mode
-
- Ensign
- Posts: 44
- Joined: Sun Jan 01, 2017 9:12 am
- Location: behind you
-
- Administrator
- Posts: 11564
- Joined: Fri Apr 25, 2003 1:38 am
Re: unable to go into cryo mode
Things look good in that screenshot for an open space save. There may be a very slight drift somehow from a control. Check the axis mappings to see if one or more of the signals is not properly centered when you center the device inputs. Then widen the deadzone on that/those axis as may be needed.
Another step to watch for is to give your ship a little more time to remove any remaining slow drift before attempting to save. Once you drop all speed to 0, give your ship an extra 5 seconds to come to a fully complete stop. This can be especially true if you've upgraded your ship recently and it's larger/heavier, thus taking more time to come to a full stop.
Another step to watch for is to give your ship a little more time to remove any remaining slow drift before attempting to save. Once you drop all speed to 0, give your ship an extra 5 seconds to come to a fully complete stop. This can be especially true if you've upgraded your ship recently and it's larger/heavier, thus taking more time to come to a full stop.
-
- Ensign
- Posts: 44
- Joined: Sun Jan 01, 2017 9:12 am
- Location: behind you
Re: unable to go into cryo mode
These are my Axis settings:
http://imgur.com/a/NG3UO
Note that throttle is actually 0 and energy control is set to +5 weapons.
Axis 6 is throttle too at 0. Hotas Warthog has two throttle levers and they are bound together in my physical hardware config.
http://imgur.com/a/NG3UO
Note that throttle is actually 0 and energy control is set to +5 weapons.
Axis 6 is throttle too at 0. Hotas Warthog has two throttle levers and they are bound together in my physical hardware config.
-
- Administrator
- Posts: 11564
- Joined: Fri Apr 25, 2003 1:38 am
Re: unable to go into cryo mode
Should be OK then. Another step you can try is hold the backspace key for 3-5 seconds, then while still holding backspace down, press the space bar to turn off the IDS. Then release backspace and try to save again. If that works, then there was likely residual throttle input being applied.
-
- Ensign
- Posts: 44
- Joined: Sun Jan 01, 2017 9:12 am
- Location: behind you
Re: unable to go into cryo mode
Indeed, this way it's working. I pressed and hold backspace, while still holding i pressed ESC and selected "save" and cryo mode was engaged.Vice wrote:Should be OK then. Another step you can try is hold the backspace key for 3-5 seconds, then while still holding backspace down, press the space bar to turn off the IDS. Then release backspace and try to save again. If that works, then there was likely residual throttle I put being applied.
Before that I tried to set a deadzone for my throttle without success.
-
- Administrator
- Posts: 11564
- Joined: Fri Apr 25, 2003 1:38 am
Re: unable to go into cryo mode
Ok, that's a good sign. It indicates that something is applying some form of forward input signal, even if extremely slight. In the meantime until/if it can be sorted, you can use that technique to lock down any velocity to absolute 0 for an open space cryo-save.